徐工RP951沥青摊铺机配件及维修

福格搅龙连接套#4608112103

文章出处:工程机械之家http://www.700618.com/人气: 发表时间:2024-07-03 10:35:44

联轴器与隔套的区别

联轴器是将两根轴连接起来、将一根轴的运动、动力传给另一根轴的联节部件,一般分成两部分,分别装在两轴的轴端。联轴器主要通过预紧来达到无空回传递扭矩,轴连接无空回,好的柔韧性和抗冲击性,允许各个方向的偏移,即使在高速下,运动也平稳,能承受大的工作量,安装操作简单方便,免维护,不需停工期,能承受高温环境,小尺寸,小惯量,电绝缘,性价比高,额定扭矩0.10-650Nm

隔套是将同一轴上的零件分隔开来的零件,在对装的轴承(角接触轴承)中间,可以调节轴承的游隙和预压;在轴承外侧装,通过间隔套,可以使紧锁螺母压紧轴承内圈的力比较均匀,也可以保护轴承不受损伤,安装时也比较有充裕空间拧螺母,好下扳手,与一般螺母靠平垫压紧的作用类似;另一方面可以在间隔圈外装油封,也保护了轴不受油封磨损。

 

免责声明丨 部分内容来源网络!本文仅供交流学习 , 版权归属原作者,部分图片、内容推送时未能及时与原作者取得联系,若来源标注错误或侵犯到您的权益烦请告知,我们将立即删除.

 

 

企业介绍

公司供应摊铺机配件,压路机配件,铣刨机配件,摊铺机刮板驱动轴,刮板驱动轴总成,找平仪,找平仪支架以及液压泵和配件。还供应摊铺机易损件,摊铺机平衡梁,搅龙轴,踏板,输料底板,叶片,熨平板,减速机,链轨,履带板,支重轮,刮板大链条,输料链条等。

 

联系人:梁经理

联系方式:13645201509

(微信同号)

QQ:2870202745

 

 

QQ邮箱:2870202745@qq.com

 

网易邮箱:LS13645201509@163.com

 

The difference between couplings and spacers

 

A coupling is a connecting component that connects two shafts and transfers the motion and power of one shaft to another shaft. It is generally divided into two parts and installed at the shaft ends of both shafts. The coupling mainly achieves torque transmission without backlash through pre tightening. The shaft connection has no backlash, good flexibility and impact resistance, allowing for deviation in all directions. Even at high speeds, the movement is smooth and can withstand large workloads. The installation and operation are simple and convenient, maintenance free, and do not require downtime. It can withstand high temperature environments with small dimensions, small inertia, electrical insulation, and high cost-effectiveness. The rated torque is 0.10-650Nm

 

Spacer sleeve is a component that separates parts on the same shaft. In the middle of the matched bearing (angular contact bearing), the clearance and preload of the bearing can be adjusted; By installing on the outer side of the bearing and using a spacer sleeve, the force of the locking nut pressing on the inner ring of the bearing can be relatively uniform, which can also protect the bearing from damage. During installation, there is also ample space to tighten the nut, which is similar to the function of a regular nut pressing with a flat pad; On the other hand, oil seals can be installed outside the spacer ring to protect the shaft from oil seal wear.

 

Disclaimer | Part of the content is sourced from the internet! This article is for communication and learning purposes only, and the copyright belongs to the original author. Some images and content were not promptly communicated to the original author. If the source labeling is incorrect or infringes on your rights, please inform us and we will immediately delete it

 

Enterprise Introduction

 

The company supplies paver accessories, roller accessories, milling machine accessories, paver scraper drive shaft, scraper drive shaft assembly, leveling instrument, leveling instrument bracket, hydraulic pump and accessories. We also supply vulnerable parts for pavers, balance beams, agitator shafts, pedals, feeding soleplates, blades, ironing plates, reducers, chain tracks, track shoes, supporting wheels, scraper chains, feeding chains, etc.

 

Contact person: Manager Liang

 

Contact information: 13645201509

 

(Same WeChat account)

 

QQ:2870202745

 

QQ email: 2870202745@qq.com

 

 

 

NetEase email: LS13645201509@163.com

上一篇:料位器线#040602 下一篇:没有了
推荐产品
$Pros$