福格铜滑块#800752573

当机械中有振动或冲击力浸染时，滑轨与滑块很可能会偏离原来的固定地位，而影响运行精度与操作寿命。因此直线导轨与滑轨滑块之间的固定就很重要。

1、推拔固定法

藉由对推拔的锁紧来施压，过大的锁紧力易造成滑轨弯曲或外侧肩部变形，所以安装时要特别注意锁紧力的适当性。

2、压板固定法

直线导轨与滑块侧面需略微突出床台与工作台边缘，而压板需加工逃槽，以防止安装时与滑轨或滑块的角部产生干预。

3、滚柱固定法

滚柱是利用螺栓头部斜度的推进来施压，所以要特别注意螺栓头部的位置。

4、定位螺栓固定法

提醒直线导轨因为安装空间的限制，使用的螺栓尺寸不可太大。

 

免责声明丨 部分内容来源网络！本文仅供交流学习 , 版权归属原作者，部分图片、内容推送时未能及时与原作者取得联系，若来源标注错误或侵犯到您的权益烦请告知，我们将立即删除.

 

企业介绍

公司供应摊铺机配件，压路机配件，铣刨机配件，摊铺机刮板驱动轴，刮板驱动轴总成，找平仪，找平仪支架以及液压泵和配件。还供应摊铺机易损件，摊铺机平衡梁，搅龙轴，踏板，输料底板，叶片，熨平板，减速机，链轨，履带板，支重轮，刮板大链条，输料链条等。

 

联系人：梁经理

联系方式：13645201509

（微信同号）

QQ：2870202745

 

QQ邮箱：2870202745@qq.com

网易邮箱：LS13645201509@163.com

 

WhatsApp:+86  13645201509

When there is vibration or impact force in the machinery, the slide rail and slider are likely to deviate from their original fixed position, which will affect the operating accuracy and service life. Therefore, the fixation between the linear guide and the slide slider is very important.

1. Push pull fixation method

By applying pressure through the locking of the push and pull, excessive locking force can easily cause the slide rail to bend or the outer shoulder to deform, so special attention should be paid to the appropriateness of the locking force during installation.

2. Pressure plate fixation method

The side of the linear guide rail and slider should slightly protrude from the edges of the bed and worktable, while the pressure plate needs to be processed with escape grooves to prevent interference with the corners of the slide rail or slider during installation.

3. Roller fixation method

The roller uses the inclination of the bolt head to apply pressure, so special attention should be paid to the position of the bolt head.

4. Positioning bolt fixation method

Reminder: Due to installation space limitations, the bolt size used for linear guides should not be too large.

Disclaimer | Some content is sourced from the internet! This article is for communication and learning purposes only. The copyright belongs to the original author. Some images and content were not promptly contacted when pushed. If the source annotation is incorrect or infringes on your rights, please inform us and we will immediately delete it

Company Introduction

The company supplies paver accessories, roller accessories, milling machine accessories, paver scraper drive shaft, scraper drive shaft assembly, leveling instrument, leveling instrument bracket, hydraulic pump and accessories. We also supply vulnerable parts for pavers, including balance beams, agitator shafts, pedals, feeding base plates, blades, ironing plates, reducers, chain rails, track plates, support wheels, scraper chains, and feeding chains.

Contact: Manager Liang

Contact information: 13645201509

(Same WeChat account)

QQ：2870202745

QQ email: 2870202745@qq.com

NetEase email: LS13645201509@163.com

 

WhatsApp:+86  13645201509